機械研究與分析 / Mechanical Research and Analysis
1 注塑機開模過程液壓沖擊與振動測試分析………………………■ 康獻民 鐘祺彬 譚艷雄 等
Test and Analysis of Hydraulic Shock Vibration in Opening Process of an Injection Molding Machine
5 基于Fluent高速列車齒輪箱泄漏量的數值分析……………………■ 汪凱 冷喬立 趙佩寧 等
Numerical Analysis on Gearbox Leakage of High Speed Train Based on FLUENT
8 基于ROS的全向巡檢機器人底盤ARM控制器設計……………………■ 韓雪 李有為 張忠 等
ARM Controller Design for Omni-Patrol Robot Chassis Based on ROS
10 8字繞障無碳小車的結構設計與分析…………………………………■ 趙春華 陳小甜 李謙 等
Structural Design and Analysis of 8-shaped Obstacle-free Carbon-free Trolley
13 老齡VLCC海上儲油風險的多層模糊綜合評價……………………………■ 李源 秦北辰 朱發新
Multi-level Fuzzy Comprehensive Evaluation of Aging VLCC Offshore Oil Storage Risk
17 礦場集輸原油處理過程VOCs排放量計算……………………………■ 劉洋 王北福 周靖也 等
Calculation of VOCs Emission during Crude Oil Processing
20 基于OpenMV的智能搬運車型機器人的設計………………………■ 施敏虎 栗云鵬 莊曙東 等
Design of Intelligent Handling Tracking Car Based on OpenMv
23 機床工作臺模態分析及拓撲優化…………………………………………■ 陳丁 康獻民 余為洲
Modal Analysis and Topology Optimization of Machine Tool Table
26 基于Fluent的泥漿脈沖發生器沖蝕磨損規律研究…………………………………………■ 王哲
Study on Erosion and Wear Law of Mud Pulse Generator Based on Fluent
29 基于Python的木板條紋與顏色檢測系統………………………………………………■ 宋鈺青
Wooden Board Stripe and Color Detection System Based on Python
32 6-UPS并聯機器人運動反解誤差建模及補償………………………………………■ 李帥 張學科
Modeling and Compensation of Motion Reverse Solution Error of 6-UPS Parallel Robot
34 一種電纜檢測機器人的結構設計與分析………………………………■ 石柯 夏斌 卞慶隆 等
Structural Design and Analysis of a Cable Inspection Robot
37 基于ANSYS的平地機前車架動態性能分析…………………………………■ 寧凡 于明 趙堅 等
Dynamic Performance Analysis on the Front Frame of the Grader Based on ANSYS
39 基于MCGS鯧魚自動變頻分揀傳送系統……………………………………………■ 梁博 張存喜
MCGS-based Automatic Frequency Conversion and Sorting Transmission System for Silvery Pomfret
43 圓弧開合式臨時頂蓋結構設計………………………………………■ 楊歡 馮棟彥 張新雨 等
Structural Design of Arc Opening and Closing Type Temporary Roof
46 光學瞄準鏡鏡身關鍵工序夾具優化設計…………………………………■ 沈偉平 王成 賈超凡
Optimum Design of Fixture for Key Procedures of Optical Sight Body
機械設計與計算 / Mechanical Design and Calculation
51 襯套旋塞閥開關力矩的影響因素及計算研究……………………………………………■ 周長寶
Affecting Factors and Calculation of Switching Torque of Bushing Plug Valve
53 高速列車線纜組件三維建模標準研究………………………………………■ 王棟 高思軍 馬力
Research on Three-dimensional Modeling Standard for Cable Assembly of High-Speed Trains
57 家用空調室外機抗颶風支架的設計校核及分析…………………………………………■ 魯文喜
Design Check and Analysis of Anti-hurricane Bracket for Outdoor Air Conditioner
60 智能惡臭測定儀嗅杯轉動裝置改進設計……………………………………………………■ 劉杰
Improved Design of the Olfactory Cup Rotating Device in an Intelligent Stink Analyzer
62 熔融堆積快速成型室結構設計與數值模擬………………………………■ 劉亞潔 何冰 陳鵬飛
Structural Design and Numerical Simulation of FDM Molding Chamber
66 海上浮動核電站檢修臨時起重支架計算……………………………………………■ 梁魁 徐楚
Calculation of Temporary Lifting Brackets for Maintenance of Offshore Floating Nuclear Power Plants
68 雙擺頭型五軸數控機床的坐標變換關系研究……………………………………■ 王馨 李憲輝
Research on Coordinate Transformation Relationship of Double Pendulum Head Five-axis CNC Machine
71 某型直升機農林噴灑系統性能分析…………………………………■ 梁偉 管華盛 張裕兵 等
Performance Analysis of a Helicopter Agriculture and Forestry Spraying System
74 修井鐵鉆工自動找中關鍵技術研究…………………………………………………………■ 趙勇
Research on Key Technologies of Automatic Centring for Workover Iron Roughneck
76 水下液壓連接器彎曲載荷試驗裝置設計………………………………■ 侯曉東 虞文 沈勇 等
Design of Bending Load Test Device for Underwater Hydraulic Connector
79 孔位置度******補償加工技術……………………………………………■ 袁祥祥 姚輝 李昂 等
Accurate Compensation Processing Technology of Hole Position
82 基于回歸分析法的光伏發電功率預測模型研究……………………………■ 姚寧 周力民 陳城
Research on Prediction Model of Photovoltaic Power Based on Regression Analysis
85 PRT安裝技術研究……………………………………………………■ 齊兵兵 曲有杰 朱國僑 等
Research on PRT Installation Technique
88 基于VTS雷達的波導裂縫天線結構方案設計………………………………………■ 李成 丁飛
Structure Scheme Design of Waveguide Slot Antenna Based on VTS Rada
90 某飛機主起落架上位鎖間隙檢測裝置的改進設計……………………■ 白亞玲 胡阿林 樊智敏
Improvement of Uplock Multiple Gap Detecting Device and Beneficial Effect of Uplock Assembly Process
92 鵝頸鉸鏈設計要點研究……………………………………………………………■ 牛福春 劉旭
Research on the Key Design Points of Gooseneck Hinge Assembly
95 基于UG的一種螺旋清角編程方法………………………………………■ 李春剛 郭輝 沈勇 等
A Kind of Spiral Scrap Chopper Programming Method Based on UG
97 一種風電聯軸器脹緊套強度校核方法……………………………■ 王習林 秦中正 胡偉輝 等
Strength Check Method for Expansion Sleeve of Wind Turbine Coupling
100 基于多級基準坐標系的車身偏差診斷方法研究…………………………………………■ 李正平
Research on Diagnosis Method of Car Body Deviation Based on Multi-level Reference Coordinate System
103 基于MATLAB軟件的機電懸掛連桿機構的運動學分析………………■ 段國柱 宋慧新 陳宇 等
Kinematics Analysis of Mechatronic Suspension Linkages Based on MATLAB Software
105 自由形狀基準特征部件幾何尺寸與公差基準系創建規則初探…………………………■ 田立群
Study on Creating Rule of Free-form Datum Feature Parts Geometric Dimensions and Tolerance
Datum System
107 電動機驅動器行星架的結構優化……………………………………………………………■ 胡濤
Structural Optimization of Planetary Carrier of Motor Actuator
110 新型機載顯示器模塊化設計研究………………………………………………■ 封振 王磊 官權
Research on Modular Design of New Airborne Display
112 一種基于變頻驅動的新型緊鏈裝置設計……………………………………………………■ 涂偉
Design of a New Tight Chain Device Based on Variable Frequency Drive
114 基于NX NASTRAN的醫用X光機C臂有限元分析……………………■ 王洪亮 劉倩 顧宸嘉 等
Finite Element Analysis on C-arm of Medical X-ray Machine Based on NX NASTRAN
117 應用MS Excel求解三參數威布爾分布函數的參數估計………………■ 劉子娟 鄭學斌 郭小軍
Parameter Estimation of Three-Parameter Weibull Distribution Function Using MS Excel
120 煤礦起重機吊重防擺控制研究…………………………………………■ 張桂欣 胡相捧 李雪偉
Research on Anti-swing Control of Coal Mine Crane
122 平臺化設計在商用空調冷水機組產品設計中的應用…………………………■ 陳賓賓 徐燕華
Platform Design in Commercial Air-conditioning Chiller Products
125 100%低地板輕軌車輛齒輪箱輸出軸密封設計及試驗驗證……………………■ 侯建文 張會杰
Design and Test Verification of Gearbox Output Shaft Seal for 100% Low Floor Light Rail Vehicle
128 基于ANSYS的汽輪發電機轉軸的過盈配合分析……………………………■ 黃鵬 任倢 張金華
Analysis on Interference Fit of Turbo Generator Shaft Based on ANSYS
131 基于有限元法的空調換熱管的塑性失穩分析……………………………………………■ 岳建軍
Analysis of Plastic Instability of Air-conditioning Heat Exchange Tubes Based on Finite Element Method
機械制造與應用 / Mechanical Manufacture and Application
134 利用NX表達式功能對曲柄銷盤參數化建模與數控編程…………■ 付躍飛 吳紅瓊 熊永釗 等
Parametric Modeling and NC Programming for Crank Pin Ring Using Expression Function in UG NX
137 高速盤端蓋成型工藝技術及裝備研究……………………………■ 呂明曉 于在洋 侯建永 等
Research on Forming Technology and Equipment of High-speed Disk End Cap
140 電主軸后培林座銑床加工工藝分析和夾具設計…………………………………………■ 曾福輝
Milling Process Analysis and Fixture Design of Rear Bearing Base in Electric Spindle
142 臥式車床加工中產生波紋的原因分析及解決對策……………………………………■ 何思琦
Cause Analysis and Countermeasure of Ripples in Horizontal Lathe Processing
145 六自由度機器人葉片剖光研究……………………………………………………■ 王剛 趙尚福
Research on Blade Polishing by using 6-DOF Robot
機械維修與診斷 / Mechanical Academic Communication
148 模流分析在塑件翹曲成因分析中的應用………………………………………■ 林國漢 王小龍
Analysis and Structural Optimization of Warpage of Plastic Parts Based on Mold Flow Analysis
151 某型燃氣輪機起動超溫故障原因分析………………………………■ 曾可卉 唐瑞 曹云鵬 等
Analysis on an Over-temperature Fault of Gas Turbine
154 撬裝式壓縮機萬向聯軸器的斷裂失效分析…………………………■ 徐春華 張鶴 孫奎峰 等
Fracture Failure Analysis of Universal Coupling of Skid-mounted Compressor |
