裝配耐磨drylin直線導向裝置的座椅確保水上安全駕駛 高速和海浪不僅為快艇帶來很多樂趣,也帶來了危險:每次船體撞擊水面時,乘客都會受到?jīng)_擊。因此需要可減緩沖擊的軸承來固定減振座椅。耐磨的igus直線軸承技術采用了免潤滑、免維護且耐腐蝕的高耐磨工程塑料,是設計師的優質之選。 乘坐快艇享受海浪、微風和陽光,是樂趣無窮的。為此,快艇設計師不僅要安裝大功率電機,還要選裝在水上旅行時也能讓乘客感到安全和舒適的座椅。比如,使用減振座椅這一具有緩沖性能且輕便的部件來應對海浪和高速。當船體撞擊水面時,船上的乘客會受到反復沖擊。而巨大的沖擊可能會給脊柱和內臟造成嚴重的損害。因此,必須使用同樣具有減振作用的軸承和導軌來固定減振座椅。很多快艇的開發人員都使用由高性能塑料制成的免潤滑且免維護的igus直線軸承技術,如波蘭的Kaj Naval公司和英國的Cobra Seats科技有限公司。 直線導向裝置可緩解快艇座椅的沖擊力 波蘭的Kaj Naval公司開發摩托艇座椅已有七年歷史。在新推出的座椅中,設計人員在彈簧式減振器中采用了igus的drylin W直線導向裝置。這一設計確保了快艇即使在高速行駛時,其座椅也能輕柔地滑動,緩解海浪帶來的沖擊。由于采用了由耐磨工程塑料制成的滑動軸承,導向裝置上的滑塊沒有側向間隙,所以即使在長時間的運行后也沒有任何磨損跡象。它的另一個優點是:這款耐腐蝕的igus解決方案不僅免維護、免潤滑,而且重量也比循環滾珠軸承系統等同類金屬解決方案要輕得多。
耐腐蝕且免維護的drylin W直線導向裝置可以減緩沖擊,提升快艇上乘客的安全性。(來源:igus GmbH)
1 注塑機開模過程液壓沖擊與振動測試分析…康獻民 鐘祺彬 譚艷雄 等 Test and Analysis of Hydraulic Shock Vibration in Opening Process of an Injection Molding Machine 5 基于Fluent高速列車齒輪箱泄漏量的數值分析…汪凱 冷喬立 趙佩寧 等 Numerical Analysis on Gearbox Leakage of High Speed Train Based on FLUENT 8 基于ROS的全向巡檢機器人底盤ARM控制器設計…韓雪 李有為 張忠 等 ARM Controller Design for Omni-Patrol Robot Chassis Based on ROS 10 8字繞障無碳小車的結構設計與分析…趙春華 陳小甜 李謙 等 Structural Design and Analysis of 8-shaped Obstacle-free Carbon-free Trolley 13 老齡VLCC海上儲油風險的多層模糊綜合評價…李源 秦北辰 朱發新 Multi-level Fuzzy Comprehensive Evaluation of Aging VLCC Offshore Oil Storage Risk 17 礦場集輸原油處理過程VOCs排放量計算…劉洋 王北福 周靖也 等 Calculation of VOCs Emission during Crude Oil Processing 20 基于OpenMV的智能搬運車型機器人的設計…施敏虎 栗云鵬 莊曙東 等 Design of Intelligent Handling Tracking Car Based on OpenMv 23 機床工作臺模態分析及拓?fù)鋬?yōu)化…陳丁 康獻民 余為洲 Modal Analysis and Topology Optimization of Machine Tool Table 26 基于Fluent的泥漿脈沖發生器沖蝕磨損規律研究…王哲 Study on Erosion and Wear Law of Mud Pulse Generator Based on Fluent 29 基于Python的木板條紋與顏色檢測系統…宋鈺青 Wooden Board Stripe and Color Detection System Based on Python 32 6-UPS并聯機器人運動反解誤差建模及補償…李帥 張學科 Modeling and Compensation of Motion Reverse Solution Error of 6-UPS Parallel Robot 34 一種電纜檢測機器人的結構設計與分析…石柯 夏斌 卞慶隆 等 Structural Design and Analysis of a Cable Inspection Robot 37 基于ANSYS的平地機前車架動態性能分析…寧凡 于明 趙堅 等 Dynamic Performance Analysis on the Front Frame of the Grader Based on ANSYS 39 基于MCGS鯧魚自動變頻分揀傳送系統…梁博 張存喜 MCGS-based Automatic Frequency Conversion and Sorting Transmission System for Silvery Pomfret 43 圓弧開合式臨時頂蓋結構設計…楊歡 馮棟彥 張新雨 等 Structural Design of Arc Opening and Closing Type Temporary Roof 46 光學瞄準鏡鏡身關鍵工序夾具優化設計…沈偉平 王成 賈超凡 Optimum Design of Fixture for Key Procedures of Optical Sight Body 51 襯套旋塞閥開關力矩的影響因素及計算研究…周長寶 Affecting Factors and Calculation of Switching Torque of Bushing Plug Valve 53 高速列車線纜組件三維建模標準研究…王棟 高思軍 馬力 Research on Three-dimensional Modeling Standard for Cable Assembly of High-Speed Trains 57 家用空調室外機抗颶風支架的設計校核及分析…魯文喜 Design Check and Analysis of Anti-hurricane Bracket for Outdoor Air Conditioner 60 智能惡臭測定儀嗅杯轉動裝置改進設計…劉杰 Improved Design of the Olfactory Cup Rotating Device in an Intelligent Stink Analyzer 62 熔融堆積快速成型室結構設計與數值模擬…劉亞潔 何冰 陳鵬飛 Structural Design and Numerical Simulation of FDM Molding Chamber 66 海上浮動核電站檢修臨時起重支架計算…梁魁 徐楚 Calculation of Temporary Lifting Brackets for Maintenance of Offshore Floating Nuclear Power Plants 68 雙擺頭型五軸數控機床的坐標變換關系研究…王馨 李憲輝 Research on Coordinate Transformation Relationship of Double Pendulum Head Five-axis CNC Machine 71 某型直升機農林噴灑系統性能分析…梁偉 管華盛 張?jiān)1?等 Performance Analysis of a Helicopter Agriculture and Forestry Spraying System 74 修井鐵鉆工自動找中關鍵技術研究…趙勇 Research on Key Technologies of Automatic Centring for Workover Iron Roughneck 76 水下液壓連接器彎曲載荷試驗裝置設計…侯曉東 虞文 沈勇 等 Design of Bending Load Test Device for Underwater Hydraulic Connector 79 孔位置度******補償加工技術…袁祥祥 姚輝 李昂 等 Accurate Compensation Processing Technology of Hole Position 82 基于回歸分析法的光伏發電功率預測模型研究…姚寧 周力民 陳城 Research on Prediction Model of Photovoltaic Power Based on Regression Analysis 85 PRT安裝技術研究…齊兵兵 曲有杰 朱國僑 等 Research on PRT Installation Technique 88 基于VTS雷達的波導裂縫天線結構方案設計…李成 丁飛 Structure Scheme Design of Waveguide Slot Antenna Based on VTS Rada 90 某飛機主起落架上位鎖間隙檢測裝置的改進設計…白亞玲 胡阿林 樊智敏 Improvement of Uplock Multiple Gap Detecting Device and Beneficial Effect of Uplock Assembly Process 92 鵝頸鉸鏈設計要點研究…牛福春 劉旭 Research on the Key Design Points of Gooseneck Hinge Assembly 95 基于UG的一種螺旋清角編程方法…李春剛 郭輝 沈勇 等 A Kind of Spiral Scrap Chopper Programming Method Based on UG 97 一種風電聯軸器脹緊套強度校核方法…王習林 秦中正 胡偉輝 等 Strength Check Method for Expansion Sleeve of Wind Turbine Coupling 100 基于多級基準坐標系的車身偏差診斷方法研究…李正平 Research on Diagnosis Method of Car Body Deviation Based on Multi-level Reference Coordinate System 103 基于MATLAB軟件的機電懸掛連桿機構的運動學分析…段國柱 宋慧新 陳宇 等 Kinematics Analysis of Mechatronic Suspension Linkages Based on MATLAB Software 105 自由形狀基準特征部件幾何尺寸與公差基準系創建規則初探…田立群 Study on Creating Rule of Free-form Datum Feature Parts Geometric Dimensions and Tolerance Datum System 107 電動機驅動器行星架的結構優化…胡濤 Structural Optimization of Planetary Carrier of Motor Actuator 110 新型機載顯示器模塊化設計研究…封振 王磊 官權 Research on Modular Design of New Airborne Display 112 一種基于變頻驅動的新型緊鏈裝置設計…涂偉 Design of a New Tight Chain Device Based on Variable Frequency Drive 114 基于NX NASTRAN的醫用X光機C臂有限元分析…王洪亮 劉倩 顧宸嘉 等 Finite Element Analysis on C-arm of Medical X-ray Machine Based on NX NASTRAN 117 應用MS Excel求解三參數威布爾分布函數的參數估計…劉子娟 鄭學斌 郭小軍 Parameter Estimation of Three-Parameter Weibull Distribution Function Using MS Excel 120 煤礦起重機吊重防擺控制研究…張桂欣 胡相捧 李雪偉 Research on Anti-swing Control of Coal Mine Crane 122 平臺化設計在商用空調冷水機組產品設計中的應用…陳賓賓 徐燕華 Platform Design in Commercial Air-conditioning Chiller Products 125 100%低地板輕軌車輛齒輪箱輸出軸密封設計及試驗驗證…侯建文 張會杰 Design and Test Verification of Gearbox Output Shaft Seal for 100% Low Floor Light Rail Vehicle 128 基于ANSYS的汽輪發電機轉軸的過盈配合分析…黃鵬 任倢 張金華 Analysis on Interference Fit of Turbo Generator Shaft Based on ANSYS 131 基于有限元法的空調換熱管的塑性失穩分析…岳建軍 Analysis of Plastic Instability of Air-conditioning Heat Exchange Tubes Based on Finite Element Method 134 利用NX表達式功能對曲柄銷盤參數化建模與數控編程…付躍飛 吳紅瓊 熊永釗 等 Parametric Modeling and NC Programming for Crank Pin Ring Using Expression Function in UG NX 137 高速盤端蓋成型工藝技術及裝備研究…呂明曉 于在洋 侯建永 等 Research on Forming Technology and Equipment of High-speed Disk End Cap 140 電主軸后培林座銑床加工工藝分析和夾具設計…曾福輝 Milling Process Analysis and Fixture Design of Rear Bearing Base in Electric Spindle 142 臥式車床加工中產生波紋的原因分析及解決對策…何思琦 Cause Analysis and Countermeasure of Ripples in Horizontal Lathe Processing 145 六自由度機器人葉片剖光研究…王剛 趙尚福 Research on Blade Polishing by using 6-DOF Robot 148 模流分析在塑件翹曲成因分析中的應用…林國漢 王小龍 Analysis and Structural Optimization of Warpage of Plastic Parts Based on Mold Flow Analysis 151 某型燃?xì)廨啓C(jī)起動超溫故障原因分析…曾可卉 唐瑞 曹云鵬 等 Analysis on an Over-temperature Fault of Gas Turbine 154 撬裝式壓縮機萬向聯軸器的斷裂失效分析…徐春華 張鶴 孫奎峰 等 Fracture Failure Analysis of Universal Coupling of Skid-mounted Compressor
1 水平旋轉摟草機彈齒運動學分析…杜韌 趙忠賢 李佳棟 等 Kinematics Analysis on Elastic Tooth of Horizontal Rotating Rake 4 一種上肢康復機器人機械臂的結構優化分析…柳海瑞 王鈺 Structural Optimization Analysis of an Upper Limb Rehabilitation Robot Manipulator 7 基于激光跟蹤儀的工裝調裝檢測技術研究…王巍 陳澤宇 Research on Tooling Adjustment and Detection Technology Based on Laser Tracker 10 甘油作非溶劑制備PEI中空纖維膜的微觀形貌分析…劉洋 王北福 Micromorphology Analysis of PEI Hollow Fiber Membrane Prepared by Glycerol as Non-solvent 14 海浪能潮汐能雙模式發電裝置設計與研究…孔凡國 張健存 劉慶 等 Design and Research of Wave Energy Tidal Energy Dual Mode Power Generation Device 18 基于ANSYS的某航空活塞發動機凸輪軸模態分析…魏武國 馮浩陽 Modal Analysis of an Aviation Piston Engine Camshaft Based on ANSYS 20 平地機鏟刀的動力學特性分析…劉聰 于明 趙堅 等 Dynamic Characteristics Analysis of Grader Blade 23 西門子系統R參數在非連續函數曲線編程中應用…卞迪 Application of Siemens System R parameter in Discontinuous Function Curve Programming 25 SiCp/Al復合材料振動輔助研拋數值模擬的研究…劉亞梅 馮潔 谷巖 等 Research on Numerical Simulation of Composite Materials Vibration Assisted Polishing 30 內燃叉車噪聲污染及降噪技術研究…褚東亮 阮榮慧 孫衛華 等 Research on Noise Pollution and Control Technology of Internal Combustion Forklift 33 基于RGB-D傳感器的同步定位與建圖方法研究…周夢妮 張國偉 盧秋紅 等 Research on Simultaneous Localization and Mapping Method Based on RGB-D Sensor 37 一種鏈板式零件的氣動可調銑削夾具…晁瑞 李志峰 Pneumatic Adjustable Milling Jig for Chain Plate Type Parts 40 基于DEFORM-3D液壓剪剪切棒料剪切質量影響因素的研究…李彬彬 傅波 衛平 Research on Influence Factors of Bars Shear Quality Using Hydraulic Shear Based on DEFORM-3D 43 聯接螺栓對鼓筒轉子臨界轉速影響的研究…劉元周 宋志佳 曹慶宇 等 Research on the Influence of Bolted Connection on the Critical Speed of Drum Rotor 45 平地機駕駛艙動力學特性研究…王志斌 于明 趙堅 等 Finite Element Vibration Analysis and Structural Optimization of Grader Cockpit 47 液壓鑿巖機雙緩沖機構動力學的仿真分析…陽復建 劉忠 Dynamics Simulation Analysis on Double Buffer Mechanism of Hydraulic Rock Drill 49 燃?xì)廨啓C(jī)傳動箱超扭保護器故障分析…胡盼 唐瑞 曹云鵬 等 Failure Analysis of Gas Turbine Transmission Box Overtorque Protector 52 65Mn彈簧鋼表面激光淬火的顯微組織及性能研究…杜成明 朱錦云 楊振 等 Study on Laser Quenched Surface Microstructure and Properties of 65Mn Spring Steel 54 3000 hp叢式井鉆機導軌雙向移運技術研究…于浩 張虎山 張鵬 等 Research on Two-way Guide Rail Moving of 3000 hp Cluster Well Rig 57 核輻射環境下機器人末端快換裝置的設計…唐瑞瑞 劉永霞 Design of Robot End Quick Change Device under Nuclear Radiation Environment 59 整車匹配檢具(TAC)的發展…沈忠民 Development of Total Assembly Checking Fixture 64 基于斷裂韌性可靠性模型的堆芯筒體快斷評價…石凱凱 劉文進 鄭連剛 等 Fast Fracture Mechanics Evaluation of Beltline Considering Reliability Models of Fracture Toughness 66 基于原機結構的機身大開口補強設計…顏凱 鮮章林 Reinforcement Design for Large Opening of Original Fuselage Structure 69 無人機視覺定位與避障子系統研究…林濤 Research on Vision Location and Obstacle Avoidance Subsystem of UAV 71 中速柴油機活塞銷的結構設計…趙飛 史乃祥 Structure Design for Medium Speed Engine’s Piston Pin 74 機電設備安裝與調試的“匠心”實踐教學…陳青艷 Ingenuity Creative Practice Teaching of Installation and Debugging for Mechanical and Electrical Equipment 76 基于VERICUT的塑料薄膜生產線鋏體加工工藝優化…宋強 Manufacturing Optimization of Tongs Body in Plastic Film Production Line Based on VERICUT 79 核電站閥門抗震分析與計算…周長寶 Anti-seismic Analysis and Calculation of Nuclear Power Plant Valves 81 軟態TP2銅材室溫抗拉強度的概率分布…張紅衛 楊帆 劉岑 等 Probability Distribution of Soft State TP2 Copper Tensile Strength at Room Temperature 86 基于SolidWorks的切割機轉軸有限元分析…周琦 Finite Element Analysis of Cutting Machine Spindle Based on SolidWorks 88 平動機構在煙草機械中的應用…吳曉飛 Application of Translational Mechanisms in Tobacco Machinery 90 尺寸數據報警的創新設計…李正平 Innovative Exploration on Dimension Data Alarming System Design 93 垃圾發電汽輪機甩負荷失敗分析與系統優化…李想 張雪 曹兵 Failure Analysis and System Optimization of Garbage Power Turbine Load Rejection 96 軸承安裝與固定的工藝參數研究…李春剛 郭輝 沈勇 等 Research on Technological Parameters of Bearing Installation and Fixing 98 長慶蘇里格油田區塊在役鉆機移運方案設計…張贏斌 侯敏 黃許澎 等 Rail-type Integral Movement Solution Design of In-service Rig at Changqing Sulige Oil Field 102 基于AMESim的鋼絲繩式隔水管張緊系統仿真分析…李歡 鄭萬里 樊春明 等 AMESim-based Study on Analysis and Simulation of Steel Cable Riser Tensioning System 105 基于DNVGL-ST-E273的深水預調試模塊結構設計…石錦坤 張藝凡 劉毅 等 Structural Design of Deepwater Pre-Debug Module Based on DNVGL-ST-E273 108 松軟低透煤層高壓水射流破煤增透技術研究…梁建明 吳瓊 Study on Breaking Coal and Coal Permeability Enhancement Technology of Medium and High Pressure Water Jet in Soft and Low Permeability Coal Seam 111 一種輕型高速料箱堆垛機的開發與應用…傅友賓 紀然 陳仕彬 Development and Application of a Lightweight High-speed Bin Stacker 113 基于MASTA軟件的齒輪嘯叫分析與解決方法…王炳善 Analysis and Solution of Gear Whine Based on MASTA Software 116 跨越式電動平板車的設計與應用…景紅濤 Design and Application of Leaping Electric Flatbed 118 頂燃式熱風爐的數值模擬研究…黃碧輝 呂遐平 Study on Numerical Simulation of Top Combustion Hot Blast Stove 121 微型泵驅動原理及其在電子設備熱管理中的應用…吳波 Driving Principle of Micro-pump and Its Application in Thermal Management of Electronic Equipment 123 高溫蒸汽管線保溫改造方案及經濟效益分析…趙輝 朱鵬 Thermal Insulation Transformation Scheme and Economic Benefit Analysis of High Temperature Steam Pipelines 125 基于平面假設求解風機彈簧減震器支反力…張文曉 Support Force Calculation of Fan Spring Shock Absorber Based on Plane Assumption 127 24 m履帶自行式仰拱棧橋與半幅仰拱模板聯合設計的研究與應用…時安琪 王柏松 武家欣 等 Collaborative Design and Application of 24 m Caterpillar Self-propelled Invert Trestle and Semi-range Invert Formwork 130 基于設計敏度的試驗機過渡段結構優化設計…鮮章林 郝琳召 李思潭 Structure Optimization of Experimental Aircraft Transition Section Based on Design Sensitivity 133 車銑復合靜壓轉臺的開發…秦建宏 劉錦輝 Development of Turning-milling Composite Hydrostatic Turntable 136 基于嵌入式處理器和LabVIEW的小型無人艇控制系統設計與實驗研究…闞亞雄 Design and Experimental Study of a Small Unmanned Boat Control System Based on Embedded Processors and LabVIEW 142 基于深度確定性策略梯度算法的雙輪機器人平衡控制研究…劉勝祥 林群煦 楊智才 等 Balance Control of Two-wheeled Robot Based on Deep Deterministic Policy Gradient 154 剪叉式高空車轉向機構結構分析…陸進添 劉丹 鄧安田 Structural Analysis on Steering Mechanism of Scissor Aerial Work Platform 61 螺旋輸送機減速電動機連接軸的斷裂失效分析…蔡小亮 Fracture Failure Analysis of Geared Motor’s Connecting Shaft in Screw Conveyor 147 某變速器中間軸齒輪斷齒失效分析…李本軍 王東霞 崔東偉 等 Broken Gear Failure Analysis of a Transmission Intermediate Shaft Gear 139 一種多墊圈少?gòu)U料沖裁的復合模具…白亞玲 Composite Die with Less Waste Material for Punching Multiple Gasket 145 A/C軸雙擺頭C軸限位技術研究…梁艷超 王剛 Research on C-axis Limit Technology of A/C Axis Double Pendulum Head 150 兩點支撐主軸裝配工藝淺析…連改紅 孔亞軍 Analysis on Assembly Process of Two-point Support Spindle 152 NX在變距螺桿建模及加工中的應用…張洋揚 Application of NX in Modeling and Machining of Variable Pitch Screw